Outdated kitchen layout with no landing zone
We measure the room and design an island that leaves 42 inches of walkway while adding a real prep surface beside the range. The layout gets planned around how you cook, not around what fits in a catalog.
A kitchen island remodel Nashville TN homeowners actually use starts with layout, not looks. We build islands that fix the traffic jam at the fridge, add the drawers you keep wishing for, and give you a real prep surface. From 12South bungalows to Green Hills two-stories, our team handles design, cabinets, countertops, and electrical so your kitchen island renovation in Nashville TN finishes on schedule.

A kitchen island remodel Nashville TN is the process of building or rebuilding a freestanding kitchen work surface: framing, cabinet boxes, countertop, electrical, and finish work tied into your existing floor and layout. We start by checking what is under the floor and inside the walls, because an island needs a solid base, a level plane, and a plan for outlets. From there it is shaker cabinets or plywood boxes, a quartz or butcher block top, and the details that make it usable daily.
Most Nashville homes we walk into have the same complaint: the kitchen has one long wall of cabinets and nowhere to land a cutting board. Older East Nashville and Inglewood houses often have a leaky kitchen sink that has already softened the cabinet base, and water damaged cabinet boxes are common behind the toe kick. If you have been searching for a kitchen island remodel near me Nashville TN, the first step is a walkthrough that measures the room and checks the floor for uneven kitchen flooring before anything gets ordered.
Every island we build covers the structure, the surface, and the electrical. Here is what is in the standard scope, and what we quote separately if your kitchen needs it.
We frame the island and set plywood or MDF cabinet boxes level and shimmed. Soft close hinges and full-extension slides come standard, and the toe kick is sealed against splashes.
We template after the cabinets are set and install quartz countertops, granite countertops, or butcher block countertops. Seams are placed where they will not catch your eye.
Island outlets and pendant lighting go on a dedicated circuit run to the NEC National Electrical Code. We pull the permit and coordinate the inspection.
A 12-inch overhang gives knee room for three or four stools. We add support legs or corbels so the top does not flex when someone leans on it.
If the island includes a prep sink, we set an undermount sink and connect a Delta, Moen, or Kohler faucet, then test for leaks before we close up the cabinet.
Caulking gun work, trim, and touch-up paint close out the job. We haul the debris and leave the room swept so you can use the island the same day.
We measure the room, check the floor for level, and use a stud finder and laser level to map what is inside the walls. You get a written scope and a price range the same visit, usually within 90 minutes.
We lay out the island footprint, seating overhang, and appliance clearances, then pick cabinet style and countertop material. You see the plan before anything is ordered, and we flag anything that would break the 42-inch walkway minimum.
Framing goes in first, then electrical rough-in for outlets and lighting on its own circuit. Cabinet boxes are set level and shimmed, and the toe kick is sealed so a future leaky kitchen sink does not soak the base.
We template the top after the cabinets are set, so the quartz or granite countertops fit the island exactly. Fabrication runs 5 to 10 business days, and install takes a few hours with the seams set where you will not see them.
Backsplash tile, caulking gun work, and final trim close it out. We test every outlet, run the faucet if there is a prep sink, and walk the island with you before we pack up. Most islands take 2 to 4 weeks start to finish.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Used to cut cabinet panels, trim, and toe kick to fit the room. Clean cuts mean tight joints and a finish that does not need filler.
The laser level sets the cabinet plane and the stud finder maps what is inside the wall before we cut for outlets or framing.
The router cuts sink openings and edge profiles; the jigsaw handles curved cuts in the countertop template and cabinet panels.
Used to trim door casings, cut out old toe kick, and clean up tight corners without tearing up the surrounding drywall.
The nail gun sets trim and paneling fast; cabinet clamps hold boxes square while the glue cures so the island does not rack.
The tile cutter handles ceramic tile backsplash work; the caulking gun lays a clean bead at the countertop and floor line.
When the island work involves ceiling changes for pendant lighting, the lift holds the drywall in place while it gets fastened.
A 12South bungalow had one wall of cabinets, a worn out cabinet run, and no landing zone beside the range. The cook prepped on the dining table and the counter stayed stacked with dishes.
We built a 6-foot island with a 24-inch depth, deep drawers, and a butcher block top, leaving 44 inches of walkway. The kitchen gained 12 square feet of work surface and the counter finally cleared off.
An Inglewood home had a leaky kitchen sink that dripped for months. The MDF cabinet boxes swelled, the island rocked, and the countertop had a hairline crack near the sink.
We pulled the wet boxes, dried the floor, and rebuilt the base with plywood cabinets. A new Moen faucet and a sealed toe kick went in, and the island sat flat with a fresh quartz top.
A Green Hills kitchen had plenty of space but no anchor. Guests stood in the living room because there was nowhere to sit, and the island was a single 4-foot cabinet with no overhang.
We built a 9-foot island with a 12-inch overhang, seating for four, a prep sink, and pendant lighting on a dimmer. The kitchen became the room everyone gathers in.
Most island calls start with a kitchen that does not work: no prep space, no storage, and a layout that fights the cook. Here is what we run into and how we solve it.
Ask a pro →We measure the room and design an island that leaves 42 inches of walkway while adding a real prep surface beside the range. The layout gets planned around how you cook, not around what fits in a catalog.
We build deep drawers, a pull-out trash bay, and a cabinet sized for the stand mixer. Full-extension slides and soft close hinges mean the storage stays usable for years.
We pull the wet boxes, dry the area, and rebuild the base with plywood cabinets sealed at the toe kick. If the leaky kitchen sink or failing kitchen faucet caused it, we fix that before the new island goes in.
We run a dedicated circuit for pendant drops and LED under cabinet lighting, then set the fixtures on a dimmer. No cords, no dark corner, and the island becomes the brightest spot in the room.
Most kitchen island remodels in Nashville run $4,500 to $18,000 in 2026, with a typical build landing near $9,000. A basic 6-foot island with stock cabinets and a butcher block top sits at the low end; a 9-foot island with quartz countertops, a prep sink, and electrical pushes toward the top. Layout changes, plumbing relocation, and premium brands like Cambria or Sub-Zero appliances move the number.
The right remodeler is the one who measures your room, shows you a written scope, and puts the same lead on the job from walkthrough to final caulk. Ask for a Tennessee Home Improvement License, a Davidson County Contractor License, and proof of insurance. Mendaro Tech carries both licenses and NARI Certified Remodeler credentials, and we will show them before you sign anything.
Yes, if the room leaves 42 inches of clear walkway on every side. Most Nashville kitchens need at least a 10-foot run to fit a useful island, and galley layouts often need a shallow 24-inch-deep version instead. We measure during the walkthrough and tell you straight whether an island fits or whether a peninsula serves the room better.
A kitchen island remodel takes 2 to 4 weeks from demo to final walkthrough in most Nashville homes. Framing and electrical rough-in take 2 to 4 days, cabinet set takes 1 to 2 days, and countertop fabrication runs 5 to 10 business days after template. If the island needs a new floor or a plumbing move, add another week.
One walkthrough, one written price range, and a crew that shows up when we say we will. Call Mendaro Tech and we will measure your kitchen, tell you what fits, and put the island on the schedule.
Book a Walkthrough (615) 909-7503 →Call (615) 909-7503 or email info@mendarotech.com and we will set up a walkthrough. We answer the phone during business hours and keep the 24/7 line open for emergencies. Most estimates get scheduled within a few business days, and we give you a written number before any work starts.