Knock down walls, open the sightlines, keep the structure sound.

Open Kitchen Remodelling Nashville TN Built for How You Actually Cook

Open kitchen remodelling Nashville TN means removing the wall between your kitchen and living space and rebuilding it so the room works as one. We handle load-bearing checks, beam sizing, electrical, and finishes for homeowners in Davidson County who want a kitchen that hosts a crowd instead of hiding the cook. If you have been searching for open kitchen remodelling near me Nashville TN, we quote the whole scope up front and start when we say we will.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mendaro Tech — your local kitchen remodeler team
Careful work. Honest options.
About this service

What Open Kitchen Remodelling Nashville TN Actually Involves

Open kitchen remodelling Nashville TN is the structural and finish work that turns a closed-off kitchen into one connected room with the living and dining space. It starts with a stud finder and a look at the framing, not a sledgehammer. We verify whether the wall is load-bearing, size a beam and posts to carry the span, pull the right permits, then reroute electrical and plumbing before any drywall comes down. From there it is cabinets, countertops, backsplash, flooring, and lighting built around the new layout.

Most Nashville homes we walk into have the same complaints: an outdated kitchen layout that cuts the cook off from guests, insufficient storage space, and poor kitchen lighting over the work zones. In older East Nashville and Woodbine houses, we also find water damaged cabinet boxes and mold behind backsplash tile once the wall opens up. A Nashville TN open plan kitchen remodeling project fixes the layout and the hidden problems in one pass, which is why we scope the demo and the rebuild together instead of treating them as separate jobs.

  • ✓ One Room, Real Sightlines
  • ✓ Storage That Works Harder
  • ✓ Light That Reaches the Whole Room
  • ✓ Resale Value That Holds
What's included

What an Open Kitchen Remodel Includes

We quote the structural work and the finish work as one scope so nothing falls between trades. Here is what is covered in a standard open-up, and what we price separately if you add it on.

✓

Structural Review and Beam

Engineer review, stamped plan, beam sizing, and post framing for load-bearing walls. We set the beam and patch the ceiling and floor so the opening looks original to the house, not added on.

✓

Permits and Inspections

We pull the Davidson County permit and coordinate the rough-in and final inspections. You get the inspection record with the closeout paperwork, which matters at resale when a buyer's inspector asks who did the structural work.

✓

Electrical and Lighting

Dedicated circuits for the range, dishwasher, and disposal, plus island outlets, recessed cans on dimmers, pendants, and LED under cabinet lighting. All work is to NEC standards and inspected before drywall goes back up.

✓

Cabinets and Countertops

Shaker cabinets from KraftMaid, Merillat, or Thomasville, with quartz countertops from Cambria, Caesarstone, or Silestone. We template the island and perimeter after the cabinets are set so the seams land where they should.

✓

Backsplash and Flooring

Ceramic tile or subway tile backsplash, plus porcelain tile, luxury vinyl plank, or hardwood flooring where the wall came out. We match the transition to the adjoining room so the floor reads as one continuous surface.

✓

Ventilation and Sink Work

Range hood ducted to the exterior, plus undermount or farmhouse sink installation with a new Delta, Moen, or Kohler faucet. We check the existing drain and disposal while the cabinet is open and replace failing parts before the countertop goes on.

How it works

How Our Open Kitchen Process Runs

01

Walk-Through and Scope

We measure the kitchen, check the wall with a stud finder, and look at the framing in the basement or attic to see which way the joists run. You get a written scope with the structural approach, finish selections, and a start date. This visit takes about 90 minutes and costs nothing.

02

Permits and Engineering

If the wall is load-bearing, we bring in a structural engineer to size the beam and posts, then pull the permit through Davidson County. That review usually takes 7 to 14 days. We do not swing a hammer on a structural wall until the stamped plan is in hand.

03

Demo and Structural Work

We protect the floors and seal off the work zone with plastic and zip walls to control dust. Demo runs 1 to 2 days. Then we set the beam, frame the posts into the wall or island, and patch the ceiling and floor. This is the loudest, dirtiest stretch, and it is also the shortest.

04

Rough-Ins and Inspections

Electrical, plumbing, and HVAC get rerouted for the new layout, then inspected before anything gets closed up. We run dedicated circuits for the range, dishwasher, and disposal, and add the range hood ducting while the ceiling is open. Rough-in and inspection usually take 3 to 5 days.

05

Finishes and Final Walk

Cabinets, countertops, backsplash, flooring, and lighting go in over 2 to 3 weeks depending on material lead times. We do a full punch walk with you, fix what is on the list, and hand over the warranty paperwork. Most open-ups land in the 6- to 10-week range start to finish.

Tools & methods

Tools and Methods We Use on Open Kitchens

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Stud finder and laser level

We map the framing and set the beam and cabinet lines dead level before any demo. A laser level keeps the island square to the room, which matters once the wall is gone and there is nothing to hide behind.

Miter saw and table saw

Trim, beam wraps, and cabinet modifications are cut on site for a tight fit. A sharp miter saw and a stable table saw setup are what separate clean casing and crown from gaps that get caulked and hoped for.

Oscillating multi-tool and jigsaw

We use these for precise cutouts in drywall, cabinet backs, and countertop templates. They let us open a wall for a beam pocket or an outlet without tearing out more than necessary.

Nail gun and cabinet clamps

Framing, trim, and cabinet installs go faster and tighter with the right gun and clamps. Cabinet clamps hold boxes flush while the screws set so the run stays straight across a long wall.

Tile cutter and caulking gun

Backsplash tile gets cut clean on a wet saw and set with consistent grout lines. A good caulking gun and the right sealant keep the sink and backsplash joints watertight, which is where most mold problems start.

Drywall lift

Ceiling patches after beam installation are safer and flatter with a lift. It holds the sheet tight to the joists while it is screwed off, which cuts the number of callbacks for cracked ceiling paint.

Real results

Before and after.

East Nashville Bungalow Wall Removal

Before

A 1948 bungalow with a load-bearing wall between the kitchen and dining room, plaster on both sides, and a single overhead light. The kitchen was 96 square feet and felt smaller because the wall blocked all the daylight from the dining room windows.

After

We set a beam sized by an engineer, removed the wall, and built a 7-foot island with a farmhouse sink and seating for four. The room now reads as 240 connected square feet, and the daylight reaches the range. The project ran 8 weeks from demo to final walk.

Green Hills Water Damage and Open-Up

Before

A slow leak under the sink had rotted two cabinet boxes and grown mold behind the backsplash tile. The kitchen was closed off from the den by a non-bearing wall, and the range hood recirculated instead of venting, so cooking smells lingered for days.

After

We treated the mold, replaced the damaged boxes, removed the non-bearing wall, and ducted a new hood to the exterior. New quartz countertops and a subway tile backsplash went in, and we added LED under cabinet lighting. The job finished in 6 weeks.

12South Galley to Open Kitchen

Before

A 90-square-foot galley kitchen in a 12South cottage, closed off by a wall with a pass-through window. Storage was limited to a single pantry cabinet, and the countertops were cracked laminate with a failing faucet.

After

We opened the wall to the living room, kept the efficient two-wall work zone, and added a peninsula with drawers on the working side. New shaker cabinets, quartz countertops, and luxury vinyl plank flooring tied the rooms together. The project took 7 weeks and gained roughly 25 percent more usable storage.

Problems we solve

Problems an Open-Up Fixes That a Paint Job Cannot

Some kitchen problems are cosmetic. The ones below are structural or layout problems, and they only get solved when the wall comes down and the room is rebuilt around a better plan.

Ask a pro →
01

Outdated kitchen layout that isolates the cook

We remove the dividing wall, size the beam, and rebuild the layout around an island or peninsula so the cook faces the living space. The result is one connected room with clear work zones and real sightlines.

↗
02

Insufficient storage space and cramped counters

We replace the wall with an island that has drawers on the working side and seating on the other, and we run full-height cabinets and a pantry run on the remaining walls. Most clients gain 20 to 30 percent more usable storage.

↗
03

Water damaged cabinet boxes and mold behind backsplash

Once the wall opens, we inspect the framing and cabinet boxes, treat any mold, replace compromised boxes, and re-seal the backsplash correctly. We fix the leaky kitchen sink or failing faucet at the same time so the problem does not return.

↗
04

Poor kitchen lighting and a range hood that does not vent

We add layered lighting on dimmers and duct the range hood to the exterior while the ceiling is open. Proper ventilation and LED under cabinet lighting over the counters change how the room feels and how it smells.

↗
Proof you can check

Licensed, Insured, and Inspected

✓
Tennessee Home Improvement LicenseTennessee Board for Licensing Contractors
✓
Davidson County Contractor LicenseDavidson County
✓
EPA Lead-Safe Certified FirmU.S. Environmental Protection Agency
✓
OSHA 30-Hour Construction SafetyOccupational Safety and Health Administration
✓
NARI Certified RemodelerNational Association of the Remodeling Industry
Good questions

Questions Nashville Homeowners Ask Before Opening Up the Kitchen

(615) 909-7503 →

Most open kitchen remodels in Nashville run $35,000 to $85,000 in 2026, with structural wall removal alone adding $8,000 to $20,000 depending on span and engineering. Cosmetic-only open-ups with reused cabinets can land near $18,000. The biggest cost drivers are whether the wall is load-bearing, how much electrical and plumbing moves, and the countertop and cabinet tier you pick. We quote the full scope up front so there are no surprise change orders mid-demo.

Yes, in most cases, but only after someone confirms what the wall does. A non-bearing partition comes out with a permit and a header if needed. A load-bearing wall needs an engineer-sized beam, posts, and a stamped plan before demo. In Nashville's older homes we also check for knob-and-tube wiring and asbestos in old joint compound before we open anything up. We handle the engineering and the permit so you are not chasing the city yourself.

Plan on 6 to 10 weeks from demo to final walk for a typical open-up. Structural review and permitting take 7 to 14 days before that clock starts. Demo runs 1 to 2 days, rough-in and inspection 3 to 5 days, and finishes 2 to 3 weeks depending on cabinet and countertop lead times. Quartz and custom cabinets can add a week or two if they are back-ordered.

The right remodeler is the one who checks the structure before quoting, pulls permits in Davidson County, and puts the scope in writing. Ask whether they use an engineer for load-bearing walls, whether their electricians are licensed, and what their workmanship warranty covers. We are a licensed Tennessee home improvement contractor and an EPA Lead-Safe Certified Firm, and we will walk you through a finished open kitchen we built nearby so you can judge the work yourself.

Ready when you are

Get Your Open Kitchen Remodelling Nashville TN Quote

We walk the kitchen, check the wall, and give you a written scope with a real start date. Licensed, insured, and permitted through Davidson County. Call (615) 909-7503 and we will set the walk-through for this week.

Call (615) 909-7503 →
Request an appointment

Call our Nashville kitchen remodeler

Call (615) 909-7503 or email info@mendarotech.com and we will set up a walkthrough. We answer the phone during business hours and keep the 24/7 line open for emergencies. Most estimates get scheduled within a few business days, and we give you a written number before any work starts.

Call anytime(615) 909-7503Email the officeinfo@mendarotech.shop
Office hoursOpen 24 hours · 7 days a week
Request received — our team will be in touch shortly.
Tap to call(615) 909-7503