Wiring, appliances and finishes done right the first time

Smart Kitchen Remodel Nashville TN Built to Work

A smart kitchen remodel Nashville TN homeowners can actually rely on starts with the stuff you never see: dedicated circuits, proper venting and cabinets hung dead level. We build connected kitchens for families in Davidson County who want the lights, locks and appliances to just work. If you are pricing a smart kitchen renovation Nashville TN, we walk the room, tell you what your wiring can carry, and quote the job before we open a wall.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dependable kitchen remodeler across Nashville, Tennessee
Careful work. Honest options.
About this service

What a Smart Kitchen Remodel Nashville TN Really Involves

A smart kitchen remodel Nashville TN is not a countertop swap with a few gadgets bolted on. It is a full kitchen build where the electrical plan comes first: dedicated 20-amp circuits for the wall oven and induction cooktop, a GFCI-protected line for the dishwasher, low-voltage runs for LED under cabinet lighting, and a neutral wire at every switch box so smart dimmers have something to talk to. We pull the old cabinets, check the framing, and set new shaker cabinets on a laser level before any quartz countertops get templated. The appliances go in last, once the rough-in is inspected.

Most Nashville kitchens we open up were wired for 1970s loads. You get two outlets on the island, a range hood that vents into the attic, and a fridge on a shared circuit that trips every time the microwave kicks on. That is the real reason people search for a smart kitchen remodel near me Nashville TN. We map the whole room against the NEC, replace worn out cabinets and water damaged cabinet boxes, and build the backbone that a high tech kitchen remodel Nashville depends on. No surprises after the drywall goes back up.

  • ✓ One App, Whole Kitchen
  • ✓ Lower Energy Draw
  • ✓ Code-Correct From Day One
  • ✓ Resale That Holds
What's included

What's Included in the Build

Our smart kitchen remodel Nashville TN scope covers the structural, electrical and finish work as one package. Appliance purchases are separate unless you want us to source them, and we will tell you up front which lines we can get faster than a big box store.

✓

Electrical Backbone and Panel Check

Load calculation, dedicated circuits for the oven, cooktop and dishwasher, GFCI protection where required, and low-voltage runs for smart switches. If the panel needs a 200-amp upgrade, that gets quoted as a line item.

✓

Cabinet Removal and Replacement

Tear-out, framing repair, and new shaker cabinets set on a laser level with soft close hinges. We check for water damaged cabinet boxes and uneven flooring before the new boxes go down.

✓

Countertop Template and Install

Quartz, granite, marble or butcher block, templated after the cabinets are set and installed with an undermount sink or farmhouse sink cut in. Typical turnaround is 7 to 10 days from template to set.

✓

Backsplash and Flooring

Ceramic tile backsplash or subway tile with clean outlet cuts, plus porcelain tile flooring or luxury vinyl plank laid over a prepped subfloor. Hardwood gets acclimated before install.

✓

Smart Appliance Install and Pairing

We set the appliances, connect them to your network, build the scenes and label the breakers. You leave with a one-page sheet showing what is on which circuit.

✓

Permits, Inspection and Warranty

Davidson County permits, rough-in and final inspections, and a 5-year workmanship warranty on the installation. EPA Lead-Safe Certified Firm protocols apply on pre-1978 homes.

How it works

How Our Smart Kitchen Remodel Process Runs

01

Walkthrough and Load Check

We spend 60 to 90 minutes in your kitchen, open the panel, and count the available breaker slots. You get a written scope with the circuit plan, cabinet layout and appliance list. Most quotes go out within 48 hours of the visit.

02

Design and Permitting

We lay out the room in 3D so you can see the island clearance and where the fridge lands. Then we pull the Davidson County permits and, if the house was built before 1978, confirm EPA Lead-Safe Certified Firm coverage before demo day.

03

Demo and Rough-In

Two to four days of tear-out, then the part that matters: new circuits, plumbing rough-in for the undermount sink, and venting for the range hood. The rough-in inspection happens before any drywall closes the walls.

04

Cabinets, Counters, Finishes

Shaker cabinets go in on a laser level, then quartz countertops get templated and set about 7 to 10 days later. Tile backsplash, porcelain tile flooring or luxury vinyl plank, and the LED under cabinet lighting follow in sequence.

05

Appliance Install and Handoff

We set the smart appliances, pair them to your network, label every breaker, and walk you through the scenes. Final inspection, then a punch list you sign off on before we load the truck.

Tools & methods

Tools and Standards We Build To

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Laser level

Sets cabinet runs and backsplash lines dead level across a 12-foot wall, which matters in older Nashville homes where the studs are not plumb.

Miter saw and table saw

Cuts cabinet filler, trim and butcher block countertops. A sharp blade and a squared fence are the difference between a tight joint and a caulk line.

Oscillating multi-tool

Cuts outlet boxes into the new backsplash and trims cabinet toe kicks without cracking tile.

Stud finder and jigsaw

Locates blocking for upper cabinets and cuts the sink opening in the countertop template.

Tile cutter and caulking gun

Clean cuts on ceramic tile backsplash and a controlled bead on the counter-to-wall joint.

Drywall lift

Holds ceiling patches in place while we close up after rerouting the range hood vent.

Circuit tracer and multimeter

Verifies which breaker feeds what before we touch a wire, and confirms the new dedicated circuits are dead before we land them.

Real results

Before and after.

Galley Kitchen, East Nashville Bungalow

Before

A 1948 bungalow with a 9-foot galley, two outlets total, a recirculating hood and cabinet boxes soft from an old sink leak. The 100-amp panel had one open slot.

After

We upgraded to 200 amps, added four dedicated circuits, replaced the cabinet run with shaker cabinets and set quartz countertops. The hood now vents outside. Total job ran 6 weeks and passed final inspection on the first visit.

Island Upgrade, Donelson New Build

Before

A 2019 build with a 6-foot island and no outlet on it. The family was running an extension cord across the floor to charge a laptop and use the stand mixer.

After

We cut in a pop-up outlet with USB, ran a dedicated 20-amp circuit through the floor, and paired the existing appliances to one hub. Two days of work, no wall demo, and the cord is gone.

Full Connected Build, Green Hills

Before

A 1990s kitchen with worn out cabinets, cracked countertops and a fridge that stuck 8 inches past the counter. The range hood vented into the attic.

After

New KraftMaid cabinets set on a laser level, Cambria quartz tops, a counter-depth panel-ready fridge, and the hood vented through the roof. The kitchen went from 180 to 240 usable square feet of storage and the job closed in 7 weeks.

Problems we solve

Kitchen Problems We Fix Before They Spread

Most of the calls we get start with one small annoyance that turns out to be a symptom. Here is what we find when we open the wall.

Ask a pro →
01

Outdated kitchen layout with no room for a fridge that fits

We re-plan the layout around the actual appliance dimensions, counter-depth or standard, and rebuild the surrounding cabinet run so the fridge sits flush and the doors open clear of the wall.

↗
02

Poor kitchen lighting and dark work zones

We zone the lighting: recessed cans on a dimmer, LED under cabinet lighting on its own smart switch, and a dedicated circuit so the two layers can run independently. Scene control ties them together.

↗
03

Leaky kitchen sink or failing faucet causing cabinet rot

We pull the cabinet, cut out the damaged section, treat and replace the subfloor, and set a new Delta or Moen faucet with a leak sensor under the sink tied into your smart hub.

↗
04

Mold behind backsplash from poor ventilation

We vent the hood to the exterior, replace the affected drywall, and re-tile with a proper substrate. Then we wire the hood to auto-ramp with the cooktop so it actually gets used.

↗
Proof you can check

Licensed, Permitted, Warrantied

✓
NARI Certified Kitchen and Bath RemodelerNational Association of the Remodeling Industry
✓
NKBA Certified Kitchen DesignerNational Kitchen and Bath Association
✓
EPA Lead-Safe Certified FirmU.S. Environmental Protection Agency
✓
Tennessee Home Improvement LicenseTennessee Board for Licensing Contractors
✓
Davidson County Contractor LicenseDavidson County
Good questions

Questions Nashville Homeowners Ask Us

(615) 909-7503 →

Most smart kitchen remodels in Nashville land between $28,000 and $85,000 in 2026, with a mid-range job around $45,000. The electrical backbone, appliance tier and countertop material drive most of the spread. A small galley refresh with smart lighting can come in near $18,000. We quote line by line so you can see where the money goes.

The right answer is the crew that pulls permits, holds a NARI Certified Kitchen and Bath Remodeler on staff, and will show you a circuit plan before demo. Ask any remodeler for their Tennessee Home Improvement License and their last three inspection sign-offs. We hand over both at the walkthrough, along with a 5-year workmanship warranty.

Start with the ones you touch daily: a smart range hood that auto-ramps with the cooktop, a connected dishwasher you can start from your phone, and a fridge with a proper panel-ready kit. Add smart dimmers on the LED under cabinet lighting and a leak sensor under the sink. Skip the gimmicks until the wiring backbone is solid.

Plan on 5 to 8 weeks for a full smart kitchen renovation in Nashville, with 2 to 4 of those days being demo and another 7 to 10 waiting on countertop fabrication. Small galley jobs run closer to 3 weeks. Add a week if we are moving plumbing or upgrading the panel to 200 amps.

Ready when you are

Get Your Smart Kitchen Remodel Nashville TN Quote

One walkthrough, one written scope, one price. We check your panel, measure the room and tell you what the job actually takes. Call (615) 909-7503 and we will get you on the schedule this week.

Book a Walkthrough (615) 909-7503 →
Request an appointment

Call our Nashville kitchen remodeler

Call (615) 909-7503 or email info@mendarotech.com and we will set up a walkthrough. We answer the phone during business hours and keep the 24/7 line open for emergencies. Most estimates get scheduled within a few business days, and we give you a written number before any work starts.

Call anytime(615) 909-7503Email the officeinfo@mendarotech.shop
Office hoursOpen 24 hours · 7 days a week
Request received — our team will be in touch shortly.
Tap to call(615) 909-7503